I’ve done two fresh installs of VS 2005 in the last 9 months. Both times, the “immediate” window wasn’t where it was supposed to be. Normally, you start a project in debug mode, hit a break point, and then in the menu, Debug|Windows, you will see Immediate.
I don’t know why, but twice now, mine’s been gone. You can find out how to open the “Command” — ctrl-alt-A. But that doesn’t have intellisense. To get the to the immediate window if it’s not showing up in your Debug|Window menu, open the “command” window and type immed and press enter.
P.S.
Or, as Sanjot points, out just press Ctrl-Alt-I. This appears to work as well.
June 22, 2007 at 11:36 am
I found this to be the case also. Very annoying. You would think it would be listed in the KB as a bug.
June 24, 2007 at 11:12 pm
I just pressed Ctrl + Alt + I and it appeared.
July 10, 2010 at 5:50 am
Thanks buddy…
August 14, 2007 at 1:57 pm
Thanks Sanjot. I get it too when I press CTRL + ALT + I
September 13, 2007 at 3:50 pm
This post should help…
Add the Immediate Window menu item to the Visual Studio 2005 menu
http://devauthority.com/blogs/razor/archive/2006/08/08/1875.aspx
September 20, 2007 at 1:45 am
Thanks! I have also faced several time. Short cut some time works some time it does not work.
As suggested in diffrent article I have use but no luck
Only luck typing in “immed” in command window.
November 28, 2007 at 3:50 am
Thanks a lot for the solution
January 30, 2008 at 3:24 pm
Found another solving, which was pretty obvious though: right click any toolbar and choose Customize (at the bottom); In the window that opens up, on the left select Debug, than in the right look for Immediate Window (a small window with a red exclamation mark) and drag&drop it into a toolbar, or in the menu that it belongs to, or both :D. And it will always be there.
February 15, 2008 at 11:40 am
For me, Ctrl+Alt+I brings up the Window Info Box – annoying. All the other solutions above worked.
April 8, 2008 at 2:45 am
this was realy helpful.
April 30, 2008 at 12:39 pm
thnx Mihai Muntenas…this is the fix!
So is the shortcut…………………….
May 19, 2008 at 1:31 am
thnks a lot
July 9, 2008 at 12:54 pm
Thanks
August 14, 2008 at 6:45 pm
Hi, I too have noticed this and went “Tools”| “Import and Export Settings” then selected to reset to ‘General Development Settings’ and all seems good now.
September 22, 2008 at 9:27 am
Tnx a lot m8, u saved my nerves today
September 26, 2008 at 12:12 am
Thanks a lot guys..both the shortcut keys and the general development setting works
October 8, 2008 at 11:11 am
Thanks a ton! It’s been missing for a week now, and I was unable to find it anywhere!
October 8, 2008 at 11:25 am
Rand, stop programming and get busy defeating the Dark One!
December 11, 2008 at 12:45 am
thanks alot man! got it now…
it was very helpful thread!. :)
May 6, 2009 at 7:41 am
Thanks a lot!
Ctrl + Alt + I did the trick!
June 16, 2009 at 10:09 am
thanks… very annoying…
July 17, 2009 at 3:48 am
Thanks Mihai Muntenas,
The procedure worked.
October 15, 2009 at 5:02 am
Where is the menu, that lets to add Inmediate Window ?
October 16, 2009 at 12:55 pm
Ctrl+Alt+I worked, thank you so much!
August 17, 2010 at 5:03 am
Tools ==> Customize ==> Rearrange Commands ==> In the Top “Menu Bar” ==> In the Dropdownlist Select “Debug|Windows” ==> Press “Add” ==> Right Side Choose the Categories “Debug” ==> Opp Side Found Command “Immediate” After that Ctrl+Alt+I Work and also u can click Debug|Windows u Found the “Immediate Window”
October 25, 2013 at 4:10 am
Thanks , your solution is so great !!!
October 31, 2013 at 12:46 am
Thanks…….. its working…